Tiffen Stands Manuel d'utilisateur télécharger pdf

Lowel Stands Instructions

Lowel light stands and

mounts are professional

lighting tools. Read both

stand and light fixture

instructions & warnings

before using.

n Not for household use.

Use only for mounting

of film and video lighting

fixtures.

n Do not mount equipment

that is too heavy.

n Extend stand sections

equally.

n Do not overextend

stands. At least 3" of each

stand section should

remain unextended.

n Extend stand base

legs fully.

n Make sure all stand

locking knobs are tight.

n Make sure all fixture

and accessory locking

screws fit into safety

undercut and rotate tight.

n Do not rig or hang

equ ipment directly over

people.

n Weights should be used

to increase stand stability.

n Use a safety cable or

cord for equipment

mounted overhead.

General Warnings

Uni, Uni TO & Uni

Sr. Stands

Extend stand legs fully as

shown for maximum stability.

When extending stand sections

to desired height, begin with

lowest section first.

Don’t fully extend any section

unless necessary. When using

with Tota/Omni, extending top

section of stand may

result in some loss

of stability. With Tota-light

mounted, rotate light head so

it lines up in parallel with one

of the legs for most sta-

ble balance. Fig.A The

3 Uni-stands can be set

up with its legs extend-

ed in tripod fashion or

Fig.B, set

flat on the floor

depending on the users

need for stability vs.

height.

Packing up

When collapsing the

Uni-stands, line up

all rotating stand

locking collars

(collars are marked

A, B, & C) with the

lowest locking col-

lar in the center

shaft

(collar

is non-

rotating &

marked D).

Slide stand legs

into notched

slots.

Tighten all

knobs.

This will

allow proper fit of Uni-stand

leg as it folds in against cen-

ter shaft & locking collars.

Omni-stand, KS

& KS Jr. Stands

When extending stand sec-

tions to desired height, begin

with lowest section first. Don’t

fully extend any section

unless necessary. See chart

above for maximum heights.

When heights greater than 9

feet are required, use the KS

or KSA Stand with a Lowel

Full or Half Pole.

Grand Stand &

KSA Stand

The Grand Stand and KSA

Stand both feature air cush-

ioning which allows the stand

section to descend gently,

preventing lamp damage.

All Lowel air-cushioned

stands have collars & locking

knobs that are black-finished.

Both stands have two holes in

the bottom of their legs that

accept Lowel Anchors and

Casters.

The Grand Stand has an

extendible leg that can be

used to keep the stand vertical

on uneven surfaces (steps,

hills, etc.). The Grand Stand

can also be nailed to plat-

forms when necessary.

When extending stand

sections to desired height,

begin with lowest section

first. Don’t fully extend any

section unless necessary.

Full Pole

& Half Pole

Lowel Poles can be used

to extend Lowel Grand

Stands, KS and KSA

Stands, to hand-hold

a light above crowds,

to extend lights

down from

overhead

clamps,

and to form booms, rigs

and various mounting and

adjusting devices.

Stand Use Note s

90 Oser Avenue,

Hauppauge, NY 11788

Call: 800 645-2522

or 631 273-2500

e-mail: inf[email protected]om

www.lowel.com

Lowel equipment and kits are sold

through authorized Lowel Dealers

and, in some countries, Authorized

Lowel Distributors. Repairs, prob-

lems, suggestions, and requests

for brochures, instructions, parts

lists may be handled by your

authorized Lowel Dealer

(Distributor) or directly with

Lowel. Electrical repairs should be

made only by Lowel or a qualified

electrician.

984

Problems, info, etc.

Lowel-Light

Manufacturing, Inc.

Stand Feature s

Lowel Stands

Uni

KSA

Ful

Pol

Half Pole

Grand Stand

Max.HeightCode

Name

Folded Length Max. Base

iameter

in. Tube Diameter

Max. Tube Diameter

Legs /

Number of Risers

Recommended Uses & NotesWeight

9' (2.7 m)

KSA

KS Stand

KSA Stand

36" (91 cm)

3'5" (1 m)

7/8" (2.2 cm)

1 1/8" (2.9 cm)

Double-strut leg brace,

tubular legs with holes

for casters or anchors.

2 Risers.

P Light, Rifa-lite 88, Fren-L 650, Basic Boom.

Industry standard medium sized stand, taller & more

stable than KS Jr.

KSA is same as KS but with air-cushioned riser

sections, black castings & knobs.

4 lbs (1.8 kg)

6.6' (2 m)KP

Full Pole

34" (89 cm) ———

7/8" (2.2 cm)

1 1/8" (2.9 cm)

2 Risers (3 sections).

Extend KS, Grand Stand. Forms: boom, background

support, rigs. Updated with extra section & additional

length for added security when used at original length.

1.75 lbs (.8 kg)

3' (91 cm)KPH

Half Pole

18" (46 cm) ———

7/8" (2.2 cm)

1 1/8" (2.9 cm)

2 Risers (3 sections).

Same as Full Pole.

1.1 lbs (.5 kg)

10.5' (3.1 m)GS

Grand

Stand

43" (1.1 m)

4'5" (1.35 m)

1" (2.54 cm)

1 3/8" (3.51 cm)

Double-strut leg brace,

tubular legs with holes

for casters or anchors.

2 Risers.

Variflector, larger/heavier lights, Big Boom.

Extra wide base, one leg extends longer for use

on uneven ground, gray anodized stand with

air-cushioned sections & direct screw clamping.

6.75 lbs (3 kg)

' (2.2 m)UN-66

ni Sr.

tand

2.5" (57.2 cm.)

3'10" (1.2 m)

3/4" (1.9 cm)

1 1/8" (2.9 cm)

ingle-strut leg brace,

solid bar legs. 3 Risers.

ota/Omni, DP Light, Rifa-lite 55 & 66, Fren-L 650,

Caselite, Scandles. Legs can lie flat to floor or in

tandard tripod arrangement, and fold up for more

ompact packing. Designed to fit into lid of Caselite.

.3 lbs (1.5 kg)

9' (2.74 m)O1-33

Omni-

stand

27" (69 cm)

3'1" (94 cm)

/2" (1.27 cm)

7/8" (2.2 cm)

ingle-strut leg brace,

solid bar legs. 3 Risers.

Tota & Omni lights, Rifa-lite 44 & small flags. Sturdy

& lightweight, an industry standard.

2.6 lbs (1.2 kg)

'11" (2.4 m)UN-55

Uni TO

Stand

1.5" (54.6 cm) 3'7" (1.1 m)

/2" (1.27 cm)

1" (2.54 cm)

ingle-strut leg brace,

solid bar legs. 4 Risers.

iP, Tota/Omni, Rifa-lite 44 & other small lights.

turdier than Uni-stand, ideal for use with Tota/Omni

in GO-85 Case.

tud has 1/4 20 screw thread.

2.6 lbs (1.2 kg)

7'11" (2.4 m)UN-33

Uni-stand

21.5" (54.6 cm)

3'7" (1.1 m)

3/8" (.95 cm)

/8" (2.2 cm)

Single-strut leg brace,

olid bar legs. 4 Risers.

ViP & other small lights. Wide base for more stability,

large locking knobs. Legs lie flat to floor or in tripod

arrangement, and fold up for more compact packing.

Stud has 1/4 20 thread. Smallest folding Lowel stand.

2.4 lbs (1.1 kg)

7'7" (2.3 m)DT-33

KS Jr.

Stand

28" (65 cm) 3'1" (99 cm)

3/4" (1.9 cm)

1 1/8" (2.9 cm)

Single-strut leg brace,

solid bar legs. 3 Risers.

ota/Omni, DP Light, Rifa-lite 55 & 66, Fren-L 650,

Caselite, Scandles. Smaller closed than KS

(for more compact packing).

.5 lbs (1.6 kg)

All Lowel Stands and Poles

are constructed with thick-

wall, anodized gun-metal gray

aluminum alloy tubing to

deliver an exceptionally high

strength-to-weight ratio.

All have a standard 5/8"

(1.59 cm) top stud with safety

undercut, adjustable base

spread and, except for

Grand Stand, collar-clamping

for each segment.

All have wall thickness of

.049" and are finished in

gun-metal gray with yellow

stand collars, except for

air-cushioned stands

(KSA & Grand Stand)

which have black

stand collars & knobs.

1 2

Résumé du contenu

Page 1 - Lowel Stands Instructions

Lowel Stands InstructionsLowel light stands andmounts are professionallighting tools. Read bothstand and light fixtureinstructions & warningsbefor

Page 2 - Booms, Supports & Rigs

The following booms areassembled from componentsdescribed on this sheet. Thesame components can be usedindividually and in other com-binations, as req

Commentaires sur ces manuels

Pas de commentaire

Tiffen Stands Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Tiffen Stands. Tiffen Stands User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Tiffen Stands