Tiffen Lowel i Light Manuel d'utilisateur télécharger pdf

The Lowel i & id-lights are profession-

al DC powered lighting fixtures.

Read these instructions and lamp man-

ufacturer’s warnings before operating.

n Not for house hold use, use only

for film, video or imaging purposes.

n The units use lamps of several

different voltages. Make certain that power

source voltage matches lamp voltage.

Example: never connect a 12 volt lamp

to a 30 volt source.

n Do not use near standing water,

or in rain.

n Units such as this emit

considerable light and heat, and if not

properly used, could be dangerous.

n Lights should not be positioned

extremely close to people. Ultraviolet light ray

emissions can cause damage to the eyes and

reddening of the skin. The likelihood of either

occurring is increased with length of expo-

sure, focus intensity and proximity. Therefore,

lights should be kept away from people.

n Avoid aiming the light at, or placing

too close to, people, delicate objects or

flammable materials.

n Do not interfere with ventilation

by covering the lights in any way.

n For proper ventilation, do not tilt

down beyond 45 degrees or operate sideways.

n Do not tilt light down if mounted on

top of a camera, while illuminated. Camera

damage could result.

n Do not leave fixtures unattended.

n Unplug fixtures when not in use.

n Never touch hot parts only touch

handles & knobs for light adjustments.

n Do not touch i or id-light upper front

end knob while operating the light,

high temperature is present.

n Lights should be operated with lamp

filament horizontal.

n Avoid mounting lights directly over

people unless secured with a safety cord

or cable.

n Keep light power cable away

from front housing when hot, to avoid

damage.

n Never store i or id-light without first

removing the power cable from the power

source.

Lowel i & id-light Instructions

Warnings

Lamp/Beam Data

Performance

i & id Power Cable

& Connectors

i & id Lamp Replacement

i-light id-light

The i-light standard power cable terminates

in a standard cigarette lighter plug.

Special i-lights are avalible with 4-pin XLR,

or Anton Bauer (2 pin battery plate, camera)

cable connectors.

i & id-light Connector

i-86 Anton Bauer

Battery Tap

The Anton Bauer connector can be supplied

by a Lowel Dealer or directly from Lowel for

installation by a qualified electrician.

NOTE: If you connect a battery with

reversed polarity (plus is minus /

minus is plus) to the id-light, the fix-

ture will not light, and a red warning

LED will illuminate on the side of the

fixture.

Yes

With 12v, 100w, 3200°K, i-100 lamp

Beam angles-points at which intensity drops

to 50% of maximum

Lamp Volts Watts °K Avg F. C. (lux) at 10' (3 m)

Code Life Flood Spot Focus Range Super Spot

i-100 12/14 100 3200 500 hr* 9 (99) 40 (430) 5:1 167 (1800)

i-55 12/14 55 3200 500 hr* 4 (40) 29 (315) 8:1 120 (1300)

*At 12v.

1 Turn focusing knob A to spot position.

2 Unscrew the small knob B located on top

of the front reflector assembly. Remove

front assembly by tilting “downward”.

3 Holding the focus knob in spot position

grasp the rear metal portion of the lamp C

and push in.

4 This will release the two “dimple” studs D

which seat the lamp in its socket.

5 While continuing to push the lamp

assembly E in, gently slide it upwards

and out of the socket. Slowly pull the

lamp forward slightly. This will expose

a single-wire connector F.

6 Separate the lamp from the single-wire

connector. Make sure single-wire

connector does not fall back into the

lamp housing.

7 Connect this wire to the replacement

lamp. Align connected lamp with the

flat side of the metal lamp base facing

down (the 4 o'clock position).

8 While pushing in, gently slide the lamp

downwards until the two “dimple” studs

are seated in the socket.

9 Replace the front reflector assembly

and tighten the top knob.

i-light Technical Data

160° constant tension

no-yoke tilting from

stand-fitting. Stand fitting can

swap for accessory handle

4.6” (11.7 cm)

3.7” (9.4 cm)

6.7” (17 cm)

Front-end comes

off for easy, no-tool

lamp change

Screw-in lock

for front-end

AC switch 20 KHz Rotary

dimmer control

Focus

knob

Stand fitting & locking knob

for 5/8” stand tops

Slot & lock for umbrella

and gel-frame

Weight:

i-light with 4' cable:

1.2 lbs (544 g)

id-light with 4' cable:

1.5 lbs (635 g)

Max wattage: 100

Max amperage: 8.3

Beam control:

continuously variable

Fits on: stands, studs,

camera tops, etc.

Materials: primarily

aluminum and Ryton

Cable: 4' (1.25 m) #16/2

with cigarette lighter

connector CE Model with

#18/2 cable

Switch: in-head

U.S. Patent: 4777566

1 2 3 4

Résumé du contenu

Page 1

The Lowel i & id-lights are profession-al DC powered lighting fixtures. Read these instructions and lamp man-ufacturer’s warnings before operating

Page 2

Lowel i & id-light InstructionsPro-light & i-lightBarndoorsBarndoor Frame Code: iP-21 Accepts swing-in accessories, and/or leaves.Rotates 360°

Page 3

Lowel i & id-light InstructionsCam-linkCode: ViP-41 Male “shoe” fitting locks intocameras with proper femaleshoe mount. Accepts Stud-linkLow-link

Page 4

id-light notes: When using the id-light, keep in mind that its lamp will shiftits color temperature warmer as the light is dimmed. If you find a parti

Modèles reliés Lowel id Light

Commentaires sur ces manuels

Pas de commentaire

Tiffen Lowel i Light Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Tiffen Lowel i Light. Tiffen Lowel i Light User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés Lowel id Light

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Tiffen Lowel i Light